Description

Brand: Yamaha

Model: DX-5

Including:

√ 1 x Binary

√ Documentation about requirements.

 

Intention:

Mono Tanz provided firmware updates for Drum machines, Synthesizers, Samplers and other Music equipment for many years, both on Reverb and eBay worldwide. We have reached a point, where it is no longer worth to run a store selling eproms with firmware, on portals like Reverb and eBay, as these websites has been widely affected with local, European and international regulations to make the administration burden and existence absurd. We still want to ensure, that end-users still have the ability to update their devices, therefore is availability & knowledge very important.

 

This is how it works:

1. After the order you will receive the Binary incl. the instructions of what Eprom(s) types you need per download link.
2. You can place an order with the binary at an online-burning service, like buyicnow.com or use your own Eprom burner.

Above will not only give you a lower price point, but also higher quality than any crook-store found on eBay or Reverb etc..

 

Introduction:

This is firmware update 6 and is the latest official released operation system by Yamaha This operation system update/upgrade requires one eprom.

 

Features

• The data load test (from the cartridge) has been added before Test # 1 (unbalanced output).
• Test program interruption (added)
• To ger out of the test program, it was previously required to tum off the power, or to press the YES button after Test # 15.
• This has been improved so that the test program can be interrupted at any time by pressing the YES button while voice memory button A-8 is pressed. When this is executed, the MIDI status will be initialized.
• For test # 1, Step 5 (check attenuate level), the output level has been changed from -21dBm to -17dBm.
• Test # 1, Step 14 (check noise level) has been added.
• The noise level should be -75dBm or below for unbalanced output terminais A,B, and P.
• Test # 2, Step 4 (check noise level) has been added. The noise level should be -75dBm or below for balanced output terminais A,B, and P.
• Test # 6 (initial touch response) has been improved so that when all keys are okay, “All key OK!” will be displayed.
• For test # 12 (OPS test), the operators for both A and B channels were checked at the same time. This has been changed so that the operator can be separately checked for its respective A or B channel. (e.g. for Step 1A, operator-1 for the channel A).
• For Test # 12, Step 8 (feedback max.) as well, channels A and B can now be separately checked.

Note:

• When the ROM version was updated from 5.0 to 6.0, the two previously used 128K-bit EPROMs were replaced by a single 256K-bit EPROM. When installing updated ROM (256K-bit EPROM) in units (s/# 2474 and below) which use two 128K-bit EPROMs, remove the two ROM ICs (IC12 and IC13) from MPII board. Then install the updated ROM in the IC12’s place. Nothing is to be installed in the IC13’s place. Reposition two jumper wires to their respective installation holes.
• The serial numbers for units using ROM version 5.0 are 1322 – 2474. This modification has been implemented on products with the serial numbers 2475 and up.

 

░░░░░░▒▒▒▓▓Why buy from MonoTanz?▓▓▒▒▒░░░░░░

⸎ Many years experience with Eproms and binaries

⸎ Free technical support. [English, German and Danish]

► Summa summārum: We provide a good product with confidence, transparency and honesty, which will improve the functionality of your equipment.

░░░░░░▒▒▒▓▓Important notes/Disclaimer:▓▓▒▒▒░░░░░░

⸎ This is the binary only, no eprom is included and therfore in the nature of the product, can refunds not be executed.

⸎ Backup any data you don’t want to lose before starting. Factory Reset is often required, when you replace the firmware to flush-out data from the old system.

⸎ Before buying, please check that you dont already have the same firmware version installed.

⸎ Please feel free to drop us a message here, per mail or over our Facebook Chat, if you have any problems or questions.