Sequential Circuits Six Trak – Version 14 Update and Diagnostic Update Upgrade OS Firmware [Download]

5,00

Description

Brand: Sequential Circuits

Model: Six-Trak

Including:

√ 2 x Binaries

√ Documentation about requirements.

Intention:

Mono Tanz provided firmware updates for Drum machines, Synthesizers, Samplers and other Music equipment for many years, both on Reverb and eBay worldwide. We have reached a point, where it is no longer worth to run a store selling eproms with firmware, on portals like Reverb and eBay, as these websites has been widely affected with local, European and international regulations to make the administration burden and existence absurd. We still want to ensure, that end-users still have the ability to update their devices, therefore is availability & knowledge very important.

 

This is how it works:

  1. After the order you will receive the Binary incl. the instructions of what Eprom(s) types you need per download link.
  2. You can place an order with the binary at an online-burning service, like buyicnow.com or use your own Eprom burner.

Above will not only give you a lower price point, but also higher quality than any crook-store found on eBay or Reverb etc..

 

Introduction:

This firmware update is based on version 14, which was the latest official released operation system by Sequential Circuits (SCI). This operation system update/upgrade requires one eprom chip. For more info, please check below.

 

To check current OS:

hold down the [Track record] button, and then press [5] on the keypad.

 

Features/improvements: [Firmware 14]

  • Version 14 upgrade provides bug fixes related to midi communication and system code issues from former firmware revisions.
  • Offers the ability to sync the on- board sequencer to non-Sequential tm MIDI Clocks
  • Unison detune has been added.  To allow storing the setting with the patch, I used the Oscillator Fine Tune parameter to control the detune amount.  If the patch does not enable Unison mode, or if MIDI mode 4 is selected, this parameter works normally.  When detune is enabled, oscillator fine tune amount is set to 0.
  • A new parameter (front panel #37 or MIDI #39) has been added.  It’s global, and is not stored with each patch.  In fact, it’s reset at power up.   This parameter has three values, 0, 1, and 2.   When it’s set to 0, all voice LFO’s behave normally.   When it’s set to 1, all voice LFO’s are reset to the “no modulation” state when the voice is assigned.   When it’s set to 2, all voice LFO’s are set to the “full modulation” state when the voice is assigned.   So this parameter allows the LFO’s to sync to the start of a new note.   It can be controlled using MIDI, the same as other parameters, but there is only one of them, not one per voice.  So all voices will have the same setting.
  • Patches can now be selected using the value pot.  In Program Select mode, the value pot will now scroll through the programs as it is turned.   Two ranges are used.  0-59 and 40-99.   When the pot is turned two steps beyond 59, the high range is selected.   When it’s turned two steps below 40, we switch back to the low range.   This may seem a little odd, but trying to cover the entire 0-99 range with the pot made the steps too close together and hard to control.   Patches can also be selected using the keypad, as before.

 

Features: [Diagnostic Rom]

This ROM is useful to localize a fault in a faulty Six-Trak.

  • Switch/LED Test
  • DAC Tests
  • RAM test
  • Sample & Hold test
  • Counter/Timer test
  • Factory Program & Sequence load & verify

 

░░░░░░▒▒▒▓▓Why buy from MonoTanz?▓▓▒▒▒░░░░░░

⸎ Many years experience with Eproms and binaries

⸎ Free technical support. [English, German and Danish]

► Summa summārum: We provide a good product with confidence, transparency and honesty, which will improve the functionality of your equipment.

░░░░░░▒▒▒▓▓Important notes/Disclaimer:▓▓▒▒▒░░░░░░

⸎ This is the binary only, no eprom is included and therfore in the nature of the product, can refunds not be executed.

⸎ Backup any data you don’t want to lose before starting. Factory Reset is often required, when you replace the firmware to flush-out data from the old system.

⸎ Before buying, please check that you dont already have the same firmware version installed.

⸎ Please feel free to drop us a message here, per mail or over our Facebook Chat, if you have any problems or questions.